MAK-TECH SEALS manufacture and stock a wide range of standard range and specific seal Types to suit all Types of Grundfos® pumps. MAK-TECH SEALS for Grundfos® are dealt with in the following Food and Dairy Seals section. Please contact us with the O.E.M. details and part numbers for cross- reference and identification, if your requirement is not shown.
MTS 192G Seals to suit Grundfos® pump ranges MAK-TECH SEALS manufacture and stock MTS 192G elastomer bellow seals designed to replace the Grundfos® seal styles “A-” and “B-” with a single, superior performing and easier to install seal design, in the majority of their centrifugal pump ranges.
MAK-TECH SEALS offer a wide range of seals to suit I.T.T. Lowara® pumps, especially centrifugal circulation pumps. Many I.T.T Lowara® pumps use standard range seals, especially MTS CS3 and MTS CS3DIN, the following Types are specific dimension seals to suit certain ranges where a standard seal cannot be installed. For other I.T.T. Lowara® requirements, please contact us with details.
MTS 130 to suit FC, FH and SH-series pumps MAK-TECH SEALS manufactures a range of ‘O’-Ring mounted conical spring seals to DIN “L1K” dimensions, to suit “FC-, FH-, SH-” series pumps.
MAK-TECH SEALS offer a wide range of seals from stock and to special order, to suit K.S.B.® equipment, especially centrifugal and waste-water pumps.
MTS 127B to suit eta- and sy- series pumps MAK-TECH SEALS manufacture and stock ‘O’-Ring mounted conical spring rotaries with MTS EBG1 boot mounted stationaries, to give operating dimensions to DIN L1N, for “ETA-” series pumps with “SY-, SYA-, SYN-, or SYT-” designations. These seals are available from stock in materials especially suitable for hot water duties.
MAK-TECH SEALS manufacture a wide range of differing elastomer diaphragm seals with ‘O’-Ring or boot mounted stationaries, to suit the specific dimensions required by various Idex® Viking® pumps, of which the MAK-TECH SEALS MTS V4 1.1/4” shaft size is a common example. Please contact us with O.E.M. details for cross reference and identification, for any other seal assembly required for this popular brand of pumps.
MAK-TECH SEALS manufacture and stock several standard range seals to suit Wilo® E.M.U. Submersible pumps, as well as MTS 1640 and 1642 seals to replace the O.E.M. “EBU” enclosed-block seals.
The MAK-TECH SEALS MTS 1640is a direct replacement for the older-generation “EBS” O.E.M. seals. Newer pumps have a slightly modified seal installed, which is directly replaced by the MAK-TECH SEALS MTS 1642. Please check the outer dimensions of the seat housing for correct identification, utilising the table below, D3 dimension.
MTS 1640 is available as complete mechanical seal assemblies or in repair kit form. The kits comprise both stationary faces, with ’O’-Rings, central rotary with elastomer diaphragm, anti-rotation pins and springs for stationaries, and retaining pins for the collets. Specify .KIT as a suffix on the stock code.
MAK-TECH SEALS make a wide range of seal parts for Alfa Laval® equipment, please contact us with the O.E.M. details for cross-reference and identification.
MTS 17B To Suit lkr Series Agitators MAK-TECH SEALS manufacture and stock 30mm and 35mm rubber-encased MTS 17B seals to suit Alfa Laval® LKR– series agitators.
MTS 19C To Suit ALC Series Pumps MAK-TECH SEALS manufacture and stock modified MTS 19 style seals to suit Alfa Laval® ALC series pumps, commonly utilised in food and dairy processes. For ALC pumps with flush housings, please see MTS 90 on following page. MTS 19C is available from stock in all three common elastomers, as well as FDA / E.C. Regulation compliant materials.
Fristam® centrifugal and lobe-rotor pumps are widely utilised in the dairy, beverage and pharmaceutical industries. MAK-TECH SEALS offer a wide range of components and complete seal sets to directly replace the O.E.M. seal components, without any modification to the seal housings or the pump seal chamber. MAK-TECH SEALS supply from stock individual seal components and complete seal sets.